Frame Material:The whole machine used 6061 aluminum profiles. Feeding height:=140mm(From base of Z axis to platform).X, Y, Z Working Area:600x900x150mm. X axis:SFU1605 Ball Screws. Y axis:SFU1605 Ball Screws. Z axis:SFU1204 Ball Screws. X axis:ø20 High intensity round rail. Y axis: SBRø20 high-strength aluminum base rails. Z axis: ø12 high-strength round rail. Stepping motor:two-phase 3A (with hand wheels). Driving Power for Stepping motor:AC220V, 240W, Output DC24V10A. Working Speed:50-1500mm/min (different material with different speed settings). Spindle motor:2200W high-speed variable frequency spindle motor, ER11 chuck, matching 6mm bur.
Variable-frequency Drive(VFD):AC220V, 2200W, 0-400Hz(built-in Control box). Tips:1, The spindle motor must connect with the VFD. 2, It cannot directly connect with the supply voltage (AC220V). 3, Please don't change the data setting of the VFD if you are not professional technicians, or it might damage the spindle motor.Drive of Stepping motor 0-3.5A adjustable four-axis driveTB6560AHQchip, 24V power supply, 2,4,8,16Subdivision settings, Factory. Cooling method:Water cooling, Matching heat dissipation water pump. Spindle precision:Radial runout=0.03mm.
Carving command:G code/TAB file/nc/TAB /NCC/file. Recommend software:computer has a USB port output. Place the control box in a ventilated dry place where there is no dust, no moisture.Connecting the control box with the CNC machine and you computer and make sure the plug will not come off. Correctly connect the machine with the controller. Don't suspended the cable which connect the Spindle motor with axis(X, Y, Z, A).
Damage the driver of the controller. Correctly install the Spindle motor and the heat pump. The heat pump should be covered completely in the water, then turned on the electric current to check whether the water-cooling system working well.
Installing a CNC control software and Drive such as the MACH 3 or EMC2on your computer. Following our manual or guideline to set the software.
Before turn on the machine, please check all the cable and water- cooling system to make sure they are working fine. You can enjoy making you dream with using our CNC machine now. Waterproof design, very durable, anti-dirt, oil spray. Dimensions: 22 x 8 x 3cm. The usb self-check light, you can type the " scroll" on the keyboard to activate it.
Directional motion control: X+, X-, Y+, Y-, Z+, Z-, A+, A. Feed rate control: F+, F. Spindle speed: speed up, slow down. Programming: E-stop, cycle start, spindle on/off, Redo, single step, original point.
Waterproof design, very durable, anti-dirt, oil spray Power by USB port Dimensions: 22 x 8 x 3cm. Directional motion control: X+, X-, Y+, Y-, Z+, Z-, A+, A- Feed rate control: F+, F- Jog rate: J+, J- Spindle speed: speed up, slow down Programming: E-stop, cycle start, spindle on/off, Redo, single step, original point.
Package Include 1 Remote controller 1 Cable. Pease note: We only sell engraver machine not include the software.
Feedback is very important to us. It is impossible to address issues if we do not know about them! Please keep the original box or packaging within 15days since item received.
Your satisfaction is our ultimate goal. We work hard to earn your trust and future business. A If you receive a defective item, you may return it or ask for a discount. Due to time zones, our reply to your questions may not be immediately. If it's non-workdays, please kindly be patient and wait till Monday.This item is in the category "Business, Office & Industrial\CNC, Metalworking & Manufacturing\Woodworking Supplies\Other Woodworking Supplies". The seller is "deerdeerd" and is located in this country: GB. This item can be shipped to United Kingdom.