FRA4 Axis MACH3 CNC Kit CW5045 Driver Controller+Nema23 Stepper Motor 425Oz-in

FRA4 Axis MACH3 CNC Kit CW5045 Driver Controller+Nema23 Stepper Motor 425Oz-in. For CNC Router Engraving Milling Machine. EU Customers don't need pay VAT or Tariff. NO Duty & NO VAT to Below Europe Countries. (425oz-in, 112mm, 3A, 1.8deg). (24-50V DC, 4.5A, 256microstep). 400W 36V 11A switching power supply. 1 x DB25 parallel cable. 4 Axis for medium size Router Mill Plasma or Laser. It can most connection 5pcs driver and control 5pcs motor in the same time. It is with 4-wire limit switch to insure our safty movement. It is with relay port to contro the cnc spindle.

Working voltage is 5VDC and support with MACH3, EMC2, KCAM4 software. 25-pin parallel port control is defined as follows.

The pin of the drive board. B(Fifth axis)pulse signal. X(First axis) pulse signal. X(First axis) direction of the signal. Y(Second axis)direction of the signal.

Z(Third axis) pulse signal. Z(Third axis) direction of the signal. A(Fourth axis) pulse signal. A(Fourth axis) direction of the signal. B(Fifth axis) direction of the signal.

CW5045 high microstep stepper motor driver. Output current: 1.3,1.8,2.3,2.7,3.2,3.7,4.2,4.5A. Mircostepping: 1(1.8°), 1/2,1/4,1/8,1/16,1/32,1/64,1/128,1/256. 1/5,1/10,1/25,1/50,1/125,1/250.

Protect form: Overheated protect, lock automatic half current , error connect protect. It is fit for NEMA17-23 two and four phase stepper motors whose current is small than 4.5A. Full current or half current choice : SW4:0=Full current; 1=half current.

To avoid use in the oil contamination, dust and corrosive gas environment. To lay it in a place with good ventilation.

Pls note the connection with right power(+ and -) to avoid broken the driver. Pls test it when confirm the connection is right.

Step angle accuracy:+ - 5%(full step, not load). Resistance accuracy: + - 10%. Inductance accuracy:+ - 20%. Temperature rise: 80deg Max(rated current, 2 phase on). Ambient temperature ----------20deg ---- +50deg.

Insulation resistance:100ohm Min, 500VDC. Insultion Strength--------500VAC for one minute. 400W, Input:100-120VAC or 200-240VAC, 50/60Hz, Output:36v/9.7 A, single output switching power supply.

Please give us the opportunityto resolve any problem when you have, we concern your problem and we will try our best to resolve it. Item must be in it's original condition and no physical damage. When you have the parcel, and not satisfied the goods or it is other problem like as broken, pls tell us the detail reason and provide the photos. The item "FRA4 Axis MACH3 CNC Kit CW5045 Driver Controller+Nema23 Stepper Motor 425Oz-in" is in sale since Saturday, April 24, 2021.

This item is in the category "Équipements professionnels\Automates, moteurs, commandes\Autres". The seller is "powace1515" and is located in Frankfurt. This item can be shipped to European Union member countries, United Kingdom.

Current: 4.5A
Holding Torque: 425oz-in
Step Angle(degrees): 1.8
Numéro de pièce fabricant: Does not apply
Driver: CW5045
Size: 57x57x112mm
Model: 4 Axis stepper motor cnc controller kit
Breakout Board: 5 Axis breakout board V5 type
Power supply: 400W 36V DC
Model Number: 23HS2430B/CW5045
Driver Microstep: 256 microstep
Software: MACH3,EMC2,KCAM4
Driver Voltage: DC24-50V
Marque: RATTM MOTOR