For CNC Router Engraving Milling Machine. Welcome European customers to our shop. We have this product in our. So it's free VAT & free import duty to you!! NO Duty & NO VAT to Below Europe Countries.
3× Nema23 stepper motor 76mm 270oz-in 3A 23HS8430. 3× Tb6600 stepper motor driver. 1× 4 Axis Mach3 USB CNC control board. 1× 350W 24V DC Switching power supply. 100% Brand New & High Quality.Nema23 Stepper motor 76mm/270Oz-in/ 3A 1.8Nm. Step angle accuracy: ±5%(full step, not load). Temperature rise: 80deg Max(rated current, 2 phase on). Insulation resistance:100MO Min, 500VDC. Insultion Strength--------500VAC for one minute. TB6600 stepper motor driver 4.5A.
The working voltage is DC 10V-45V. It is recommended to use switching power supply DC32V for power supply. Adopt 6N137 high-speed optical lotus root to ensure high speed without losing step. Using Toshiba's new high-current, high-voltage TB6600HG brand new original chip, with low-voltage shutdown, overheating shutdown and over-current protection circuits, and short-circuit protection added compared to TB6560. The rated maximum output reaches: ±4.5A.
Suitable for nema17 nema23 and nema34 two-phase/four-phase/four-wire/six-wire stepper motors within 4.2A. Subdivision: full step, half step, 1/4 step, 1/8 step, 1/16 step, maximum 16 subdivisions. The working voltage is DC 10-45V; it is recommended to use DV32V switching power supply. There are two input terminals, both of which adopt the common anode input mode.The level of the input pulse is 5V, if it is a 12V level pulse, a 1K resistor is required, if it is a 24V level pulse, a 2.4K resistor is required. The motor runs when the CLK has pulses, and automatically enters the set half-current state when there is no pulse, and the motor is locked. The motor rotates forward when CW is high or suspended, and reverses when it is low. When EN is high or floating, it is working state, when it is low, it is offline. The power supply cannot be connected reversely, otherwise the chip will be burnt out. The set current should not exceed the rated current of the motor. Mach3 USB motion control board 4 axis. The motion control card for machine control, with strong professional. Requires the operator to have the relevant expertise! Please strictly follow the instructions and warnings before using this product. If you are not familiar with the product and software features, make sure the machine's power switch on hand, you can quickly turn off the power. It is recommended that the limit switch and emergency stop switch must be installed first and can be used normally. This USB motion card does not need install any USB driver, Windows2000/XP/Windows7, can directly identify.
4-axis linkage, Maximum step-pulse frequency: 100KHz, support connect four stepper motor drives or servo drives. Signal Output:0-10V, it can control the spindle motor speed through using mach3 software.
4 general-purpose opto-couplers isolation input : can connect the limit switch, emergency stop. 4 general-purpose isolated relay drive output interface, can drive four relays for controlling the spindle starts, forward rotating and reverse rotating, pumps or other device. Support for connecting electronic handwheel. Note: the output singal of theelectronic handwheel must be 5V, more than 5V output will damage the hand wheel interface. 350W 24V DC switching power supply.
DC output: 24V 0-14.5A. DC voltage of Adjustable range: ±10%. AC input voltage range: 115VAC/6.5A/50HZ----230VAC/3.4A/60HZ; Selected by switch. Overload protection: 105%-135% cut off the output, automatic recovery. Over-voltage Protection: 115%-150% shut down O/P voltage, re-power on to recover.
Withstand voltage: I/P-O/P: 1.5KvAC; I/P-FG: 1.5KvAC; O/P-FG: 1.5KvAC; 1minute. Please check out your address carefully when processing order. We are not responsible for wrong or undeliverable address. 1530 workings days to most other countries. When you have the parcel, and not satisfied the goods or it is other problem like as broken, pls tell us the detail reason and provide the photos, we will help you to solve any problems.We work hard to make sure EVERY CUSTOMER 100% satisfaction. This item is in the category "Business, Office & Industrial\Industrial Automation & Motion Controls\Other Automation Equipment". The seller is "powace1515" and is located in this country: CH. This item can be shipped to United Kingdom, European Union.