DE4 Axis Offline stand alone USB Motion Controller&MPG Handwheel f/ CNC Router

DE4 Axis Offline stand alone USB Motion Controller&MPG Handwheel w/ E-Stop. For CNC Router Engraving Milling Machine. New items have arrived our. We will send the item from.

Tschechische Republik by DHL to EU Countries. Tschechische Republik to below EU Countries. CNC offline Motion Controller System RMHV3.1. 1 x Pendant Handwheel MPG. 1 x 8GB USB Flash drive.

4 Axis PLC Controller 500KHz off-line. RMHV3.1 is the 4 axis and 4 axes motion controller which has been researched and developed by RATTM MOTOR CNC for four years. The control period of each position is only 4 milliseconds, with a high control precision. The highest uniaxial output pulse is 500KHz and the pulse width can be adjusted.

It supports the common stepper motor and servo motor. Numerical control system adopts the ARM+FPGA design framework. The ARM can finish the part of human-computer interface and code analysis and the FPGA can finish the part of underlying algorithm and control pulse generate, with the reasonable design, reliable control and easy operation. The panel layout structure of. The CNC MOTION SYSTEM Controller can be finished only by 17 keys and it supports the FANUC with high universality to be compatible with G code set.

This manual introduces the operation method of the. The machine tool and the operation procedure of the machine tool. By lots of graphical representation and examples, the uses can quickly learn to use the. 1.2 Performance parameter of Product.

1 Ordinary digital input interface of 16-circuitoptocoupler coupling isolation. 2 Ordinary digital input interface of 3-circuit optocoupler coupling isolation. 3 Output interface of 0-10V spindle control port with analog quantity(can be modified as PWM output). 4 Support the 4 axis stepper motor control, the highest control pulse output of single axis is 500KHz. 5 ARM9 main control chip.

6 FPGA core algorithm chip. 7 4.3 inches TFT screen, resolution ratio: 480272. 9 The main control equipment is 18V-32V power input, the current capacity is required not to be lower than 0.5A.

10 Support the USB flash disk to read the G code, and the size of G codefile has no requirement. 11 Be equipped with MPG port and support digital display MPG as well as support the general MPG in the market. 12 Support the panel key with single-axis manual operation, manual step and CONToperation.

13 Support the operation of quickly specify the running position. 14 Support the multi coordinate systems (with automatically saving function in case of power cut).

15 Support the function of saving data automatically after power down (press the start to automatically save the data in the operation, automatically save the data after power down). 1.3 Outward Appearance, Structure and Size. Adopts the embedded shell structure, which can punch a square hole on the equipment cabinet and then embed this equipment in the squire hole.

Use two locking mechanism from the inside can fix this equipment on the equipment cabinet, with easy installation. The panel size of the product is 163mm102mm5mm.

The size of main body is 156mm93mm45mm. The size of square hole installed on the equipment cabinet is 156mm93mm. The front of the product is 17 user keys and 1 4.3and 480272 LSD (Liquid Crystal Display), and the reverse side is input signal, spindle control, stepper/ servo control, MPG and other four sets of interfaces as well as USB interface and power interface. Please look at the reference picture 1-3 and picture 1-4 in detail. This USB Interface is the standard USB socket of A-type, attached a 50cm USB extension cord with installation lugs. Outward Appearance, Structure and Size. The RMHV2.1 adopts the embedded shell structure, which can punch a square hole on the equipment cabinet and then embed this equipment in the squire hole. As the picture shows, the wiring section of this controller totally has power interface, USB interface, MPG port, stepper/servo control output interface, spindle control output interface, ESTOP limitprobe and other input interface as well as 6 interfaces with different functions. The power interface is 5.08mm wiring terminal. As the picture shows, the right wiring terminal is the positive power, and the left wiring terminal is the negative power, accepting the power supply of 24V-32V DC with direct -current supply. The current capacity is required to be more than 0.5A. The MPG port picture is showed as the Picture. From the reverse side of the product, it is the 8+9 double raw interface which is close to the USB interface. Stepper motor driver wiring picture. The connection between system and stepper motor driver. As the picture shows, the second group of interface from the right side is the stepper/servo control output interface. The interface of third group from the right side is the spindle control output interface. In the spindle control output interface, the start and stop of spindle (M3/M5), cooling liquid (M8/M9), lubricating oil (M10/M11)s three output terminals are totally the signal of open ground.

The highestelectric current can be absorbed is 20mA. The speeding governing output terminal can output 0-10V adjustable voltage. It can adjust the speed of spindle motor by adjusting the F value of spindle and outputting to the frequency converter. Can control the VFD, frequency conversion spindle only needs 2 signals and one is the start-stop control and the other is speed control/Speeding governing output (0-10V).

ESTOP limit probe input interface. The interface of group one from the lift side is the ESTOP probe input interface.

This interface contains three kinds of input signals, including the external-expansion start and stop, probe and limit/home. FRO: the FRO mainly refers to adjust the FRO value to amend the current feed rate under the situation that the F value has been confirmed before the processing course or in the processing course. The actual rate F#=setting rate FFRO. SRO: the SROrate mainly refers to adjust the SROrate to amend the current speed of spindle under the situation that the S value has been confirmed before the processing course or in the processing course.

The actual speed of spindleS#=setting rate S SRO. SRJ: SRJ, under the situation that the defaultvalue ofmanual operation rate has been set, it is impossible to set the value again to amend the manual operation rate when it is required to adjust the manual operation speed and CONToperation speed.

At this moment, the SRJ value can be modified to realize the purpose of amending the manual operation speed. The actual speed of manual operation FS#=setting manual operation speed SRJ. F: Feed rate, the unit is mm/min. For example F=2000, indicates that it can feed 2000mm per minute.

S: speed of spindle, the unit is rad/min. For example S=20000, indicates that it can rotate 20000 per minute. X: The coordinate code of X axis. Y: The coordinate code of Y axis.

Z: The coordinate code of Z axis. A: The coordinate code of A axis. Busy: Server busy, it cannot conduct the processing operation, and parts of the function are open. For example, amend the FRO and value of SRO. REDAY: REDAY mode, any operation can be done at this time, including the processing or modifying the parameter or starting the 2nd mode.

Reset: reset mode, all the operations are forbidden to do at this time. CONT:continuous operation, each axis can conduct the CONT operation under this mode. Step:Manual step modeeach axis can conduct the manual step operation under this mode.

MPG: MPGMode, each axis can conduct the MPG operation under this mode. AUTO: Automatic processing mode, it will show AUTO when enters the state of automatic processing.

Pendant Handwheel with Emergency stop. CNC system and position control of various mechanical devices, mainly for CNC machine tools and various mechanical zero correction and signal division. 100 times per revolution slightly cracking point, 100 pulses per revolution output, holding the handle of the panel and all-metal high-grade design. Metal code disc, high precision, good texture.

Easy installation, shaped thin, ultra-light. Voltage, single-ended, differential in three output options provide 100PPR pulse output options. Driver output type, anti-interference ability, long-distance transmission. Oil, water, dust-proof design (grade IP65) spiral stretch 20 million guaranteed.

Novelty, easy to move, interference, load capacity. Full plastic shell, insulation, high strength, anti-oil seal design.

With × 1, × 10, × 100 third gear ratio, enabling 4-12 axis magnification switch. With the control switch, emergency stop switch optional, easy to operate. For CNC machine tools, printing machinery, numerical control equipment. OFF, X, Y, Z, 4. About us: Our company is an emerging professional Cross-Border Electronic company.

We guarantee every product is of high quality and durable utility compared to other factories becayse we choose the best-buys goods. When you have the parcel, and not satisfied the goods or it is other problem like as broken, pls tell us the detail reason and provide the photos, we will help you to solve any problems.

The item "DE4 Axis Offline stand alone USB Motion Controller&MPG Handwheel f/ CNC Router" is in sale since Friday, July 2, 2021. This item is in the category "Business & Industrie\Automation, Antriebe & Motoren\Elektromotoren\Schrittmotoren". The seller is "powace08" and is located in Zuerich. This item can be shipped to European Union member countries, United Kingdom.

Marke: RATTM MOTOR
Herstellernummer: Does not apply
Angebotspaket: Nein
Axis: 4
Application: CNC Router Milling Lathe machine
Ausländisches Produkt: Nein
Modifizierter Artikel: Nein
Frequence: 500KHz
Name: 4 axis CNC Motion controller
Input power: 24-32VDC