40 kinds of G command codes support cyclical drilling. Full screen editing of program for your parts. Built in 256M memory for storing N pieces of parts programs.
USB Interface: Support reading, writing, data backup and direct processing for your U disk file. (DNC) - I/O 24/24: It is flexible to use, for its I/O ports can be expanded to 96/96. Two Languages: Chinese and English operation interfaces for convenient operation.
Adopts advanced algorithm for small lines, processing stably. Supports fast operation in specified position and multi-coordinate system (automatically saving after power down).
Supports saving break-point function: It will automatically save by pressing the PAUSE button during operation or after powering off. Supports multi-level operation authorization for easy management, featuring time-limited system locking function.Supports for G code files of third-party software, including UG, Mastercam, PowerMill, FeatureCAM, ArtCAM, JDPaint, Wentai. Basic Functions: - Number of Controlled Axes: 4-Axis(X, Y, Z, A) - Number of Linkage Axes: Full Linkage - Analog Spindle: 1 - Spindle Rate: 10% to 150% - Minimum Instruction Unit: 0.001 mm - Maximum Instruction Value: ±99999999 x Instruction Unit - Fast Feed Speed: 12,000mm/min - Rate of Feed: F0, 25%, 50%, 100% - Cutting Feed Rate: 12,000mm/min - Feed Speed Rate: 10% to 150% - Electronic Gear Ratio: 1-65535:1-65535 - Automatic Acceleration & Deceleration: Yes - Location: G00 (Linear Interpolation Location) - Interpolation: Linear (G01), Circular (G02/G03/G12), Spiral-line Interpolation - Returning to Reference Point: Automatically (G28) - LCD: 3.5-inch TFT LCD screen with resolution of 480 x 320 - MDI Softkey: 5 - Step Feed Amount: x1, x10, x100 - Communications Interface: U disk interface - External Handwheel Interface: Yes - I/O Interface: 24/24 (Extensible to 96/96) - Pause (seconds): Yes - Accurate Stop Status: Yes - Accurate Stop: Yes - Storage Travel Checking: Yes - MDI Running: Yes. It supports multi-segment operation - Reset: Yes - Jump Switch: Yes - Single Block Operation: Yes - Program Protection Switch: Yes - Self-diagnostic Function: Yes - Emergency Stop: Yes - Power Supply: Single-phase AC220V+10%-15%, 50Hz±1Hz.
DC24V/1A - Coordinate Systems: Machine Coordinate System (G53), Workpiece Coordinate System (G92, G54-G59), Local Coordinate System (G52), Plane Designation of Coordinate System - Automatic Coordinate System Setting: Yes - Decimal Point Input: Yes Auxiliary Function: - Auxiliary functions: M2 digits, M code customization, manual/MDI/automatic control of spindle forward, reverse and stop; control of lubrication to start and stop, etc. Spindle Functions: - Spindle Function: Analog Spindle (0-10V) Editing Operation: - Editorial Functions: Parameters, Diagnostic Bit Input, Program Editing, MDI Multi-segment Execution - Storage Capacity: 256M - Number of Stored Programs: N pcs - Display of Program Names: Chinese, English, Numbers, and Combinations - Looking for Program Lines: Yes - Skip Optional Program Segment: Yes - Program Switch: Yes Display: - Displayed Language: Chinese, English - Processing Time & Number of Parts: Display - Spindle Speed, M/S Instruction: Yes. 1 x XC609DD 4-Axis CNC Offline Controller. Usually it cost about 35USD-50USD. The item "4 Axis CNC Offline Controller Motion Control Stepping Servo Numerical Control" is in sale since Thursday, June 20, 2019.
This item is in the category "Business & Industrial\Industrial Automation & Motion Controls\Drives & Starters\Drives & Motor Controls\Stepper Controls & Drives". The seller is "pincei" and is located in Shenzhen.This item can be shipped worldwide.