GerCNC 3018 Offline Control 3Axis GRBL Milling Cut Wood PCB Engraving Machine. We will send the item from Germany by DHL to EU Countries. GRBL Control 3 Axis CNC laser machine kit (without laser). 1 x GRBL Control Board. 10 x 20°0.1mm drill bits.1 x Set of allen wrench. 1 x 4G USB Flash drive include User manual & GRBL Software. 100% Brand New and High Quality!! CNC Router Mini 3018 GRBL Desktop Pcb Wood Engraving Milling Machine. Body used profiles and plastic, small size, light weight, USB interface, GRBL control system, learning, entry preferred.
Can use carving knife, but also can use laser engraving. Can be engraved plastic, wood, acrylic, pvc, pcb, wood and the other similar material. Spindle : 775 spindle motor (12-36V). Step motor : Fuselage length 34MM, Current 1.33A, 12v. Power supply : 24V 5.6A.Support System: Windows XP / Win 7 / Win 8 / Win 10 / Linux. Drill bits: tip 0.1mm , 20 degree , diameter3.175mm. Laser: Support 500mw 405nm 12v / 2500mw 450nm 12v / 5500mw 450nm 12v. GRBL USB port cnc engraving machine controlle board. Stepper motor: support 24V 2A. Spindle motor: support 24V 10A (supports PWM0%-100%).
Master chip: atmel 328P (arduino nano). Spindle drive chip: MOSFET (recommendation 1236V, current : within 10A). Support stepper motor: 12V, maximum current of 2A or less is recommended within 1.5A and additional heat. (Any stepper motor 42, 57).Power Interface: 5.5-2.5mm DC interface. Support system: win-xp, win7, win8, win10. Add the outer casing: mainly for the bare board of the control board, short circuit problem during use add the power button switch (this switch is the power supply control signal, there is no large current passing through the switch, do not worry about the switch size) Cancel the drive module, integrated imported stepper motor drive, with short circuit protection, no need to worry about module damage. And integrated heat dissipation aluminum alloy add the fan to force heat dissipation. Add offline recognition to insert offline modules and computers at the same time.
Offline will automatically identify if there is computer control. Can support 20,000 rpm spindle.Support for larger power spindles. Improved power interface: original plastic interface changed to full metal shielded interface. Improved USB interface: The original USB interface is patch soldering, transport collision and improper use, easy to drop, now changed to plug-in, very strong.
The spindle drive increases the optocoupler isolation, which makes the control board generate less heat, and the spindle speed adjustment is more linear and safer. The stepper motor drive increases the self-recovery fuse. When a short circuit or fault occurs, the power supply is cut off and the fault indicator light is displayed. The 12V step-down increases the self-recovery fuse. When a short circuit occurs, the power can be cut off in time to avoid damage.
Optimize layout, control area and drive area separation, run more stable. SD shows it is SD card condition, turn on power supply after insert SD card, otherwise, it won't work. SD card capacity 4G could be recognized. Press X- or X+ button to switch.
Control Press confirmation button to access manually controlling page. File Press confirmation button to access file page. Set Press confirmation button to access setting page. On the off-line controller, buttons control corresponding actions.
SPN is spindle controlling, should press SPIN. Fan is fan controlling, should press SMOD. Note: To exit this page, should press back button longly.
After exit, save the current location as engraving starting point X0Y0Z0. Note: system can recognize max 100 available files one time. Tap could be recognized not support files with long name.
Press Y+ or Y- to choose files need to be engraved, press confirmation button to access engraving page. Press ok to start engraving. If you want to stop during engraving, press back button longly, then back to the file selection page machine will not stop at once, as GRBL controller has already saved a part of G code, will stop after carry out completely. The left words show the machine moving distances every time you press the button on the condition of manually controlling, press Y+ or Y- to choose, default 1mm each time. The right words show Communication baud rate setting, default 9600.
After setting, press confirmation button to save, then press back button to exit setting page. Note: the setting parameters can not be saved on the condition of electricity outage, it will be default value when turn on next time. The item "Ger CNC 3018 Offline Control 3Axis GRBL Milling Cut Wood PCB Engraving Machine" is in sale since Monday, March 22, 2021.This item is in the category "Uhren & Schmuck\Juwelierbedarf\Goldschmiedewerkzeug\Graviermaschinen". The seller is "powace08" and is located in Zuerich. This item can be shipped to European Union member countries, United Kingdom.