Controller Axis Cnc

4 Axis Offline Stand Alone Replace Mach3 USB CNC Controller Handwheel MPG

4 Axis Offline Stand Alone Replace Mach3 USB CNC Controller Handwheel MPG
4 Axis Offline Stand Alone Replace Mach3 USB CNC Controller Handwheel MPG
4 Axis Offline Stand Alone Replace Mach3 USB CNC Controller Handwheel MPG
4 Axis Offline Stand Alone Replace Mach3 USB CNC Controller Handwheel MPG

4 Axis Offline Stand Alone Replace Mach3 USB CNC Controller Handwheel MPG   4 Axis Offline Stand Alone Replace Mach3 USB CNC Controller Handwheel MPG
DDCSV1 is the 4 axis linkage motion controller which is developed through 4 years of research and development; each position control cycle 4 ms, high control precision. The highest single output pulse is 500KHz, and the pulse width is adjustable. Support common stepper motor and servo motor. DDCSV1 numerical control system uses ARM+FPGA design framework, ARM to complete the man-machine interface and code analysis, FPGA complete the underlying algorithm and control pulse generation part. Reasonable design, reliable control, convenient operation. DDCSV1 panel layout is reasonable, the 17 key to complete common offline operation, support for the general purpose of FANUC G code compatible. This manual introduces the operation method of the DDCSV1, the machine tool and the operation procedure of the machine tool.

Through a large number of illustrations and examples of the use of the DDCSV1 can learn to use the faster the CNC system. Ordinary digital input interface of 16-circuitoptocoupler coupling isolation. Ordinary digital input interface of 3-circuit optocoupler coupling isolation.

Output interface of 0-10V spindle control port with analog quantity(can be modified as PWM output). Support the 4 axis stepper motor control, the highest control pulse output of single axis is 500KHz. 4.3 inches TFT screen, resolution ratio: 480272. The main control equipment is 18V-32V power input, the current capacity is required not to be lower than 0.5A. Support the USB flash disk to read the G code, and the size of G codefile has no requirement. Be equipped with MPG(hand wheel) port and support digital display MPG as well as support the general MPG(hand wheel) in the market. Support the panel key with single-axis manual operation, manual step and CONT operation. Support the operation of quickly specify the running position.

Support the multi coordinate systems (with automatically saving function in case of power cut). Support the function of saving data automatically after power down press the start to automatically save the data in the operation, automatically save the data after power down. Outward Appearance, Structure and Size. The DDCSV1.1 adopts the embedded shell structure, which can punch a square hole on the equipment cabinet and then embed this equipment in the squire hole. Use two locking mechanism from the inside can fix this equipment on the equipment cabinet, with easy installation.

The panel size of the product is 163mm102mm5mm. The size of main body is 156mm93mm45mm. The size of square hole installed on the equipment cabinet is 156mm93mm. 1 CNC system and position control of various mechanical devices, mainly for CNC machine tools and various mechanical zero correction and signal division. 2 100 times per revolution slightly cracking point, 100 pulses per revolution output, holding the handle of the panel and all-metal high-grade design.

3 Metal code disc, high precision, good texture. 4 Easy installation, shaped thin, ultra-light.

5 DC 5V power system. 6 Voltage, single-ended, differential in three output options provide 100PPR pulse output options. 7 Driver output type, anti-interference ability, long-distance transmission. 8 Oil, water, dust-proof design (grade IP65) spiral stretch 20 million guaranteed. 1 Novelty, easy to move, interference, load capacity. 2 Full plastic shell, insulation, high strength, anti-oil seal design. 3 With × 1, × 10, × 100 third gear ratio, enabling 4-12 axis magnification switch. 4 With the control switch, emergency stop switch optional, easy to operate. 5 For CNC machine tools, printing machinery, numerical control equipment. 1 x 4 axis motion controller. 1 x 8GB USB Flash Drive. 1 x USB Extension Cable.

The item "4 Axis Offline Stand Alone Replace Mach3 USB CNC Controller Handwheel MPG" is in sale since Friday, April 9, 2021. This item is in the category "Consumer Electronics\Other Consumer Electronics". The seller is "power116" and is located in ShenZhen ,Guangdong. This item can be shipped worldwide.

  • Compatible Brand: POW
  • Type: POW
  • Compatible Model: Universal
  • Model: POW
  • Brand: Unbranded


4 Axis Offline Stand Alone Replace Mach3 USB CNC Controller Handwheel MPG   4 Axis Offline Stand Alone Replace Mach3 USB CNC Controller Handwheel MPG