Controller Axis Cnc

4 Axis 12NM C/L Stepper NEMA34 Hybrid Servo CNC power supply Controller Chuck

4 Axis 12NM C/L Stepper NEMA34 Hybrid Servo CNC power supply Controller Chuck
4 Axis 12NM C/L Stepper NEMA34 Hybrid Servo CNC power supply Controller Chuck
4 Axis 12NM C/L Stepper NEMA34 Hybrid Servo CNC power supply Controller Chuck
4 Axis 12NM C/L Stepper NEMA34 Hybrid Servo CNC power supply Controller Chuck
4 Axis 12NM C/L Stepper NEMA34 Hybrid Servo CNC power supply Controller Chuck
4 Axis 12NM C/L Stepper NEMA34 Hybrid Servo CNC power supply Controller Chuck
4 Axis 12NM C/L Stepper NEMA34 Hybrid Servo CNC power supply Controller Chuck
4 Axis 12NM C/L Stepper NEMA34 Hybrid Servo CNC power supply Controller Chuck
4 Axis 12NM C/L Stepper NEMA34 Hybrid Servo CNC power supply Controller Chuck
4 Axis 12NM C/L Stepper NEMA34 Hybrid Servo CNC power supply Controller Chuck

4 Axis 12NM C/L Stepper NEMA34 Hybrid Servo CNC power supply Controller Chuck    4 Axis 12NM C/L Stepper NEMA34 Hybrid Servo CNC power supply Controller Chuck

12NM Closed Loop Stepper Motor. NEMA34 Hybrid Servo CNC +. Power supply + Mach 3 motion card+ Mach3 wireless handwheel+.

4-Jaw Chuck , motor drive , power supply, Tailstock all cables. HBS860H is a two-phase hybrid stepper motor servo driver, adopting new 32-bit control technology and vector control technology that can prevent loss of movement synchronization and ensures accuracy. High-speed moment of force attenuation is far lower than the traditional open-loop driver, which can greatly increase high - speed performance and torque of stepper motor. Load-based current control technology can effectively reduce temperature rise of motor and prolong motor service life. Built-in position and alarm output signal is convenient for PC monitoring and controlling.

Position out-of-tolerance alarm function ensures machining equipment safe operation. The driver is a great replacement for traditional open loop stepping driver and can replace part of traditional AC servo system. The driver uses advanced 32-bit special motor control chip and vector closed-loop control technology. Stepping closed-loop circuit system, no loss of movement synchronization. Improve motor output moment of force and speed.

Current is adjusted depending on the load, reducing motor temperature rise. Fit for all kinds of machinery load conditions (including low rigidity belt wheel and pulley) without adjusting the gain parameters. Motor runs smoothly, vibrates mildly, and improves acceleration and deceleration dynamic performance. Zero speed static ability of no vibration after completion of positioning. Impulse response frequency is up to 200kHz.

Maximum 51200 steps/rotation, 16 kinds of optional segment. It supports over current protection, over voltage protection, position out-of-tolerance protection. Peak Output Current: 8.0A (current changes along with load). Motor Moment of Force: 12N.

Encoder B phase input +. Encoder A phase input +.

(Incorrect encoder wiring will cause driver or encoder damage). If control signal level is 5V, no need to connect resistor to signal input. If control signal level is 12V, a 1K resistor need to be connected to signal input in series. If control signal level is 24V, a 2K resistor need to be connected to signal input in series.

OC door output, close indication location is complete, open indication location is incomplete. OC door output, close indication has alarm signal, open indication has no alarm signal.

Green light is on when power on. Red light flashing once within 3 seconds indicates over-current or interphase short circuit; red light flashing twice within 3 seconds indicates over-voltage; red light flashing three times within 3 seconds indicates position out-of-tolerance protection. The item "4 Axis 12NM C/L Stepper NEMA34 Hybrid Servo CNC power supply Controller Chuck" is in sale since Friday, September 11, 2020.

This item is in the category "Industrial\Industrial Automation & Motion Controls\Electric Motors\Stepper Motors". The seller is "mjenterprizekecaj" and is located in churchill.

This item can be shipped worldwide.
  • MPN: Does Not Apply
  • Brand: Unbranded

4 Axis 12NM C/L Stepper NEMA34 Hybrid Servo CNC power supply Controller Chuck    4 Axis 12NM C/L Stepper NEMA34 Hybrid Servo CNC power supply Controller Chuck